Details of Pumps
Pumps and its capacities are essential for dewatering for foundation works for Bridges and Buildings.
Cut sections of various pumps are as shown below.
A three-phase induction motor. The stator winding is clearly visible, with its red and black insulation. The rotor is also partially visible, with its copper bars embedded in the iron core. The yellow box on the end of the motor likely contains the terminal block for connecting the motor to the power supply.
Here are some of the key components visible in the image:
- Stator: The stationary part of the motor that contains the winding.
- Rotor: The rotating part of the motor that contains the conductor bars.
- Winding: The coil of wire that carries the electrical current.
- Terminal block: The connection point for the power supply.
Induction motors are widely used in industrial applications because they are relatively simple, reliable, and efficient. They are often used to drive pumps, fans, compressors, and other machinery.
A submersible pump cut in half. The pump consists of two main components:
- Motor: The electrical motor that powers the pump.
- Pump: The mechanical device that moves the water.
The motor is located on the left side of the image and is a three-phase induction motor. The stator winding is clearly visible, with its red and black insulation. The rotor is also partially visible, with its copper bars embedded in the iron core.
The pump is located on the right side of the image. It consists of a centrifugal impeller, a volute casing, and a shaft. The impeller is a rotating device that creates a centrifugal force that pushes the water out of the pump. The volute casing is a spiral-shaped chamber that collects the water from the impeller and directs it out of the pump. The shaft is the rotating component that connects the motor to the impeller.
These Submersible pumps are used to pump water from deep wells. They are often used in agriculture, industry, and domestic water supply.
a centrifugal pump cut in half. The pump consists of a casing, an impeller, and a shaft.
The casing is the outer part of the pump that contains the impeller and the shaft. The impeller is a rotating device that creates a centrifugal force that pushes the water out of the pump. The shaft is the rotating component that connects the motor to the impeller.
These Centrifugal pumps are used to pump water from one place to another. They are often used in agriculture, industry, and domestic water supply.
a reciprocating pump cut in half. The pump consists of a cylinder, a piston, a connecting rod, and a crank.
The cylinder is the hollow part of the pump that contains the piston. The piston is a moving part that moves back and forth within the cylinder. The connecting rod connects the piston to the crank. The crank is a rotating part that converts the linear motion of the piston into rotary motion.
These Reciprocating pumps are used to pump liquids, such as water, oil, and chemicals. They are often used in industrial applications, such as water supply, oil refining, and chemical processing.
a centrifugal pump casing. The pump casing is the outer part of the pump that contains the impeller and the shaft. The impeller is a rotating device that creates a centrifugal force that pushes the water out of the pump. The shaft is the rotating component that connects the motor to the impeller.
These Centrifugal pumps are used to pump water from one place to another. They are often used in agriculture, industry, and domestic water supply.
a submersible pump cut in half. The pump consists of two main components:
- Motor: The electrical motor that powers the pump.
- Pump: The mechanical device that moves the water.
The motor is located on the left side of the image and is a three-phase induction motor. The stator winding is clearly visible, with its red and black insulation. The rotor is also partially visible, with its copper bars embedded in the iron core.
The pump is located on the right side of the image. It consists of a centrifugal impeller, a volute casing, and a shaft. The impeller is a rotating device that creates a centrifugal force that pushes the water out of the pump. The volute casing is a spiral-shaped chamber that collects the water from the impeller and directs it out of the pump. The shaft is the rotating component that connects the motor to the impeller.
These Submersible pumps are used to pump water from deep wells. They are often used in agriculture, industry, and domestic water supply.
A multistage centrifugal pump cut in half. The pump consists of multiple stages, each of which has a centrifugal impeller and a volute casing. The impellers are arranged in series, so that the water is pumped through each stage in turn. This type of pump is used to pump water to high pressures.
0 Comments
If you have any doubts, suggestions , corrections etc. let me know